CEB Press/Manufacturing Instructions

THIS PAGE IS FOR THE CEB PRESS

This page gives you all the information you need to make your CEB Press from stock steel and parts. The steps in Mechanical Fabrication and Electronic Components are independent of each other, but within each category, the suggested order should be followed. Once you finish both, you can continue on to Final Machine Integration. At that point, your machine can be used.

Mechanical Fabrication

The purpose of this section is to build and assemble all mechanical components of the CEB. You must first cut the steel, then fabricate individual parts, then assemble them, and then paint the machine.

Steel Cut List

• Cut the steel into the following lengths.
• Label and separate cuts by "Step" number so you can easily find cuts for each step during the fabrication stage.
• Note: Item Number and part number refer to CAD information. This is un-necessary if you are following the fabrication steps listed.
• Also, from the sheet, torch the Hopper Sheet Metal and the simple plates.

Link to printable page.

Parts Fabrication

The purpose of this section is to assemble the cut steel into individual parts and assemblies.

• Please see this spreadsheet for what steel each step requires.

Structural Components

1. Simple Plates
2. Frame structural support components

Shaker

3. Shaker Mount
4. Shaker Hammer and Shaft
5. Shaker Hydraulics

Hopper and Grate

6. Hopper and Grate Supports
7. Hopper Sheet Metal
8. Hopper Mounting plate
9. Grate

Machine Core

10. Soil Loading Drawer
11. Roller Guides

Main Frame Preparation

12. Wide Cylinder Supports
13. Main Frame Small Components
14. Main Frame U-Channel Prep-Still needs fab drawings

15. Make the Press Feet
16. Prepare the main cylinder

Main Frame Assembly

17. Assemble U Channel
18. Fit the Main Cylinder
19. Stretch the frame
20. Weld the spacers
21. Install Small Components
22. Fit the Drawer Members

Hydraulics

• Hoses - Secondary cylinder hose unit

Parts Assembly

The purpose of this section is to assemble all of the parts you made in the parts fabrication section.

1. Assemble the structural components
2. Assemble the Soil Loading System
3. Shaker Assembly
4. Adjust the Drawer
5. Install the secondary cylinder
6. Hard-line the main cylinder

Paint

• Cover the hydraulics and any other place that should not be painted.
• Check all external surfaces for sharp edges and smooth with angle grinder.
• Remove any surface rust with wire brush and / or sandpaper.
• Apply a thorough coating of paint to all steel surfaces.
• Allow 24 hours to dry before handling.

Electronic Components Assembly

1. Linked Extension Cord
2. Sensor Unit
3. Case
4. Solenoid Driver v2
5. Controller Box

Final Machine Integration

1. Mount Solenoid Valve Set And Controller Box x
2. Electrohydraulic Integration
3. Code Upload

The Global Village Construction Set
Habitat	CEB Press	Cement Mixer	Sawmill	Bulldozer	Backhoe
Agriculture	Tractor	Seeder	Hay Rake	Well-Drilling Rig
	Microtractor	Soil Pulverizer	Spader	Hay Cutter	Trencher
	Bakery Oven	Dairy Milker	Microcombine	Baler
Industry	Multimachine	Ironworker	Laser Cutter	Welder	Plasma Cutter
	CNC Torch Table	Metal Roller	Rod and Wire Mill	Press Forge	Universal Rotor
	3D Printer	3D Scanner	CNC Circuit Mill	Industrial Robot	Chipper Hammermill
	Drill Press	Induction Furnace
Energy	Power Cube	Gasifier Burner	Solar Concentrator	Electric Motor Generator	Hydraulic Motor
	Steam Engine	Heat Exchanger	Wind Turbine	Pelletizer	Universal Power Supply
	Nickel-Iron Battery
Materials	Aluminum Extractor	Bioplastic Extruder
Transportation	Car	Truck
Key	Design	Planning	Prototype	Almost done	Full Release